Page 1 of 4

4th gen bits

Posted: Sat Oct 20, 2012 12:30 pm
by wurlycorner
Hi all,

Upgrade bits wanted for a 4th gen H22;
  • Mugen or Tri-Y manifold/downpipe

    OEM Red/Black interior
Also after some random bits to sort out niggly things on both my 4th gens;
  • JDM (no fog light cut out) rear bumper, paint colour unimportant

    Plug with pigtails from any of the centre-console switches (e.g. front fogs, half mast switch etc)

    Front undertray (with any fixings if poss) Looks like this;
    Image

    Drivers side rear arch 'liner' (the small plastic trim bit that goes at the back of the arch between the bumper and the inner arch) Looks like this;
    Image

    Both sides outer door seals (the one on the door that goes all over the top of the door frame)

    Standard steering wheel with air bag and leather trim (replace the crap plastic one in the JDM), this might be from UKDM cars only?

    Clips from the under bonnet sound deadener (round push in mushroom clips that hold it to the underneath of the bonnet) plus measurement of what size hole they go into

    Spare wheel tool holder polystyrene insert (with tools if poss - pic nicked from Pushki);
    Image

    Small plastic clip that holds the throttle cable onto the alternator wiring cover over the top of the rocker cover

    Drivers side door lock jam (the hook bit that mounts on the B pillar)

    UKDM fuse box complete (the one inside the cabin, drivers footwell)

    JDM main instrument binnacle (the clock/fuel/temp gauge section). MUST be TCS version


All the oem bits in that list need to be in good/perfect nick as they're to replace bits we already have but 'aren't right'...

-----------------------------------------------------------------------------------------------------------------------------------
Bits I wanted but have now already got;
  • Passenger side inner door seal (the one that goes on the shell up the B pillar, over the top and down the A pillar) - No longer required - Thanks JDM-BB4
    white plastic insert for the vtec solenoid plug, goes in the plug in the pic below - complete plug cut off the loom and sent to me complete would be fine) - No longer required - Thanks jjmartin
    Image
    Rad breather hose clip, unbroken) - No longer required - Thanks vanzep
    Image
    Also need the bracket for this bit (fuel cutoff switch?) please - No longer required - Thanks Bludge and jjmartin
    Image
    (Noticed that the bracket on the JDM has sheared, as shown here...)
    Image
    Boot seal - No longer required - Thanks JDM-BB4
    Mud flap screws (the stainless self-tappers that hold on the mud flaps, arch liners etc) - No longer required - Thanks JDM-BB4
    UKDM sidelights (both sides) - No longer required - Bri has these for me, thanks
    2x Door open switches - now got, thanks Jon
    Door handle lock barrel trim, the rare design one - No longer required - vanzep has this for me, thanks
    To help, this is the type I'm after the lock barrel trim for (this one has the trim bit missing)
    Image
    Looks like this front on (with trim missing)
    Image
    The 'normal' type handle looks like this (with the trim missing)
    Image
    The difference in the trim piece I'm after is it's smaller and goes in from behind the handle, whereas the normal one (bottom pic) goes in from the outside
[/list][/list]

Posted: Sat Nov 03, 2012 9:17 pm
by wurlycorner
Bump

Posted: Sun Jan 20, 2013 7:46 pm
by wurlycorner
Updated after some success lol

Posted: Sun Jan 20, 2013 9:14 pm
by honda-hardy
UKDM sidelights (both sides)...

I may still have these, ill take a look tomorrow.

Posted: Wed Mar 06, 2013 10:28 pm
by wurlycorner
Edited the post yesterday, but forgot to bump!

Posted: Wed Mar 06, 2013 10:30 pm
by Bri
You still need side lights bud? I have a set.

Posted: Wed Mar 06, 2013 10:48 pm
by wurlycorner
Yeah, still after all that lot except the door switches.

Posted: Fri May 31, 2013 3:46 pm
by vanzep
pretty sure i can solve the lock barrel trim for you. i just replaced one of the doors on my lude yesterday and as i swapping out the barrels i noticed they had two different type of trims as shown in the pics below. The smaller black one goes in from the back and the larger silver one goes in from the front. The black one should be perfect for you :)
I dont want money for it but i do want to swap it for a 2 little plastic parts im needing.
Image
Image

Posted: Fri May 31, 2013 4:13 pm
by honda-hardy
What plastic parts you after?

Posted: Fri May 31, 2013 4:43 pm
by wurlycorner
That black one is the badger, excellent thanks!

What's the parts you're after?