Page 1 of 5
Crank pulley - Common fault?
Posted: Wed Jul 11, 2012 9:35 pm
by nitin_s1
Sooooo.. Guess what happened?
Crank pulley wobbled out of it's place again. Same scenario as my old SiR.
Driving and then all of a sudden power steering was lost then had to emergency stop on the side of the road.
Called the AA but he couldn't tow it home due to the car being too low so had to wait 2 hours for a big tow truck to lift the car.
I think I will need a new crank pulley and few new belts (I think I have some that Phil sent me last time - Cheers 4thgenphil
). Just as last time, I'm hoping that nothing has happened to the timing belt
I can go get a crank pulley from VTECdirect at £150+ but if anyone has one that they would like to sell then it would be sexily awesome.
I'm not gutted about that I have to spend money on it, gutted about coming to see everyone at LLL meet and that skittles vodka.
Posted: Wed Jul 11, 2012 9:38 pm
by Ammo
Just get an alloy one off ebay if they fit the Gay-S much cheaper
Posted: Wed Jul 11, 2012 9:45 pm
by vanzep
seems to have happened to a few people Nitin - hope you get it fixed ok - phil also helped me out with an oem crank pulley - saved the day.
Posted: Wed Jul 11, 2012 10:04 pm
by nitin_s1
Phil is sexy, I've offered him to have sex with me and loose my virginity. I owe him big time.
The cheap pulley from eBay - is it any good?
Posted: Wed Jul 11, 2012 10:15 pm
by vanzep
Merlin says the lightweight pulley is good
There was an article on pro and cons but id say if you cant get an oem one at a reasonable price then deffo go for the ebay one-make sure its the right one with 6 ribs on the main pulley
Posted: Wed Jul 11, 2012 10:19 pm
by nitin_s1
I'll have a little read tonight.
Posted: Wed Jul 11, 2012 10:22 pm
by Merlin
vanzep wrote:Merlin says the lightweight pulley is good
My engine hasnt blow up yet
Nits, a bit of reading on the cheapo underdrive pulley:
http://www.ludegeneration.co.uk/honda-p ... t1991.html
Read up on the pro's and cons.
Posted: Wed Jul 11, 2012 10:27 pm
by Merlin
And
PerformanceAutoworks wrote:The H22 crank pulley IS NOT a harmonic damper - the rubber is an isolator - there is a difference.
The rubber isolator's main point of being is to isolate the crankshaft from the loads and vibrations caused by running several components at varying loads at the same time (AC, PAS, Alt) and the need to run the belts at quite a high tension - the AC being the biggest load
With the PAS and AC removed there is 100% absolutely no issue with running a BALANCED solid alluminium item which can also have the PAS section machined off to suit this application.
With AC removed I also have no issues with suggesting or running alluminium pullies even if PAS is retained as belt tension can be reduced. I still ALWAYS recommend balancing the pully before fitting though.
I have run many motors "built" or otherwise in both road trim and race trim with solid ally pullies with no consequence at all.
My one concern is when wanting to run one and retaining the AC as well - I do not recommend this for the reasons mentioned above. Having said that I have installed several at the request of customers with no issues.
http://www.ludegeneration.co.uk/honda-p ... 56-10.html
I still have my PAS and AC in my 5th, which has the alloy underdrive pulley
Posted: Wed Jul 11, 2012 10:28 pm
by nitin_s1
But I have my AC on most of the times. Would that be a problem?
Posted: Wed Jul 11, 2012 10:34 pm
by Ammo
I had unorthodox under drive pulleys on my old engine, never had a problem, Sir_Chris ditched it for a OEM honda one and it failed
Seems the build quality is better in the aftermarket stuff