Congratulations to vtecmec for winning May/June's Lude Of The Month, with his DIY Turbo BB1 build.
>>> Click Here For Profile <<<
>>> Click Here For Profile <<<
BB1 Scrapyard Dog - first 1/4r mile run
- vanzep
- Supporter 2016
- Posts: 6977
- Joined: Sun Jan 29, 2012 6:38 pm
- My Generation: 4G
- Location: Edinburgh
- Has thanked: 254 times
- Been thanked: 394 times
BB1 Scrapyard Dog-Sill inspection and new fwing
I have never inspected the sills on this car - so after 3 years owbership decided to take a brave pill and go for it
I was also planning on replacing the front wing as it had many stone chips and scratches and a bubble or two of rust.
Here is what i found:
Sill was ok so removed leaves and mud and cleaned it up.
Sprayed 2 cans of anti rust cavity wax inside the full length of the sill - quick bit of derust at the back corner, bit of bodyfiller and some paint.
Sideskirt refitted using new clips.
Front wing area had the same leaves and crud and some small areas of rust. All treated and painted and new front wing fitted.
Also had a look at the butterfly valve in the resonator part of the intake under the front wing. Saw it was rusty - looked a bit closer and saw the metal shaft the operates the butterfly was snapped clean off.
So i decide to remove the resonator. Car sounds and goes a bit better now
Will need to come back to the intake when i decided if im staying stock or replacing it with a long arm true cold air kit or something that actually adds power
Not a bad afternoons work but still got the other side to go.
Paint match on the front wing is perfect.
I was also planning on replacing the front wing as it had many stone chips and scratches and a bubble or two of rust.
Here is what i found:
Sill was ok so removed leaves and mud and cleaned it up.
Sprayed 2 cans of anti rust cavity wax inside the full length of the sill - quick bit of derust at the back corner, bit of bodyfiller and some paint.
Sideskirt refitted using new clips.
Front wing area had the same leaves and crud and some small areas of rust. All treated and painted and new front wing fitted.
Also had a look at the butterfly valve in the resonator part of the intake under the front wing. Saw it was rusty - looked a bit closer and saw the metal shaft the operates the butterfly was snapped clean off.
So i decide to remove the resonator. Car sounds and goes a bit better now
Will need to come back to the intake when i decided if im staying stock or replacing it with a long arm true cold air kit or something that actually adds power
Not a bad afternoons work but still got the other side to go.
Paint match on the front wing is perfect.
1996-2000 1993 EG9 Blue Civic 1.6 Vti - Traded in against the BB4
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC
- vanzep
- Supporter 2016
- Posts: 6977
- Joined: Sun Jan 29, 2012 6:38 pm
- My Generation: 4G
- Location: Edinburgh
- Has thanked: 254 times
- Been thanked: 394 times
BB1 Scrapyard Dog PLM & EIBACH
thanks for the kind comments but no nasty surprises on the driver side just hope the passenger side is as good
was hoping to get round to making a start on the other side today but rain halted any progress.
so updated the to do list:
fix high level brake light or fit new bootlid with led in spolier - high level brake light now fixed 29/7/2019
check passenger side sills and treat with cavity wax - work completed 2/8/2019
small dents taken out of passenger side rear arch and trated from inside with cavity was and new membrane fitted. completed 5/8/2019
fit front passenger wing - work completed 2/8/2019
align front bonnet and polish up the headlights or swap for refurbed units
oil and filter change - work completed 29/7/2019
notch front subframe ready for plm manifold. completed 7/8/2019
fit new exhaust plm tri-y mani and decat the car - booked in for w/c 12/8
possibly upgrade/change air intake
fit new passenger door
check valve clearances
fit new thermostat & gasket & coolant pipe (side of block to water valve)
polybush rear suspension & possibly upgrade shocks/springs back and front - new eibach springs rcvd 8/8/2019
have the roof painted - sunroof has already been done by bodyshop
paint and fit jdm rear bumper and move fog light to drivers side rear cluster
by the time thats all done it will probably be time to look at the rear arches
was hoping to get round to making a start on the other side today but rain halted any progress.
so updated the to do list:
fix high level brake light or fit new bootlid with led in spolier - high level brake light now fixed 29/7/2019
check passenger side sills and treat with cavity wax - work completed 2/8/2019
small dents taken out of passenger side rear arch and trated from inside with cavity was and new membrane fitted. completed 5/8/2019
fit front passenger wing - work completed 2/8/2019
align front bonnet and polish up the headlights or swap for refurbed units
oil and filter change - work completed 29/7/2019
notch front subframe ready for plm manifold. completed 7/8/2019
fit new exhaust plm tri-y mani and decat the car - booked in for w/c 12/8
possibly upgrade/change air intake
fit new passenger door
check valve clearances
fit new thermostat & gasket & coolant pipe (side of block to water valve)
polybush rear suspension & possibly upgrade shocks/springs back and front - new eibach springs rcvd 8/8/2019
have the roof painted - sunroof has already been done by bodyshop
paint and fit jdm rear bumper and move fog light to drivers side rear cluster
by the time thats all done it will probably be time to look at the rear arches
Last edited by vanzep on Thu Aug 08, 2019 6:12 pm, edited 6 times in total.
1996-2000 1993 EG9 Blue Civic 1.6 Vti - Traded in against the BB4
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC
- Drax
- Moderator
- Posts: 6267
- Joined: Wed Dec 22, 2010 4:05 pm
- My Generation: 4G
- Location: Wrexham, North Wales
- Has thanked: 16 times
- Been thanked: 379 times
BB1 Scrapyard Dog-Sill inspection and new fwing
excellent work there ive never bothered to check out my sills.....yet
2.2 JDM DOHC SI-VTEC LSD TCS 4WS ABS BB1 MANUAL 1992
FOR PAUL
FOR PAUL
- JEBB4
- Supporter 2014
- Posts: 1225
- Joined: Tue Feb 18, 2014 7:28 pm
- My Generation: 5G
- Location: Australia
- Has thanked: 78 times
- Been thanked: 62 times
BB1 Scrapyard Dog-Sill inspection and new fwing
Lookin good there mate, for a car residing in the UK!! My bb4 was a mess and that was 4-5 years ago!
My BB6 buildJamie P 2013 wrote:i like tits
viewtopic.php?f=17&t=54187
My BB2 build (yang)(WRITTEN OFF AND SOLD)
viewtopic.php?f=17&t=18866
My BB4 build (yin) (SOLD TO DRAX)
viewtopic.php?f=17&t=12087&hilit=JEBB4+ ... ty#p203321
- vanzep
- Supporter 2016
- Posts: 6977
- Joined: Sun Jan 29, 2012 6:38 pm
- My Generation: 4G
- Location: Edinburgh
- Has thanked: 254 times
- Been thanked: 394 times
BB1 Scrapyard Dog-Sill inspection and new fwing
Got the passenger side done earlier today
The sideskirt was full of mud and stones but the sills themselves cleaned up with a quick wipe of a cloth - was a bit surprised that there was zero corrosion
Also fitted the new front wing.
The sideskirt was full of mud and stones but the sills themselves cleaned up with a quick wipe of a cloth - was a bit surprised that there was zero corrosion
Also fitted the new front wing.
1996-2000 1993 EG9 Blue Civic 1.6 Vti - Traded in against the BB4
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC
-
- Supporter 2016
- Posts: 2665
- Joined: Thu Feb 23, 2012 8:28 pm
- My Generation: 4G
- PSN GamerTag: spaz_ma_taz
- Location: Edinburgh
- Has thanked: 13 times
- Been thanked: 50 times
BB1 Scrapyard Dog-Sill inspection and new fwing
It's hard to believe where this car came from! I knew I was right to point you in its direction
- vanzep
- Supporter 2016
- Posts: 6977
- Joined: Sun Jan 29, 2012 6:38 pm
- My Generation: 4G
- Location: Edinburgh
- Has thanked: 254 times
- Been thanked: 394 times
BB1 Scrapyard Dog-Sill inspection and new fwing
Yeah thats right - i had seen it advertised a few times on ebay so it had caught my eye before that.
1996-2000 1993 EG9 Blue Civic 1.6 Vti - Traded in against the BB4
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC
- vanzep
- Supporter 2016
- Posts: 6977
- Joined: Sun Jan 29, 2012 6:38 pm
- My Generation: 4G
- Location: Edinburgh
- Has thanked: 254 times
- Been thanked: 394 times
BB1 Scrapyard Dog PLM & EIBACH
Making good progress.
Front sub frame has been notched ready for the PLM manifold.
Ive mocked the new exhaust parts up on a spare H22a head - just trying to work out how to mate it up to the 60mm centre section once the oem cat is removed. Think ive got it covered
The Eibach Springs have arrived - so i can fit them to the OEM shocks and see a 25- 30mm drop all round or might possibly wait until i have a found a set of Koni Sports as they are a brilliant combo
Front sub frame has been notched ready for the PLM manifold.
Ive mocked the new exhaust parts up on a spare H22a head - just trying to work out how to mate it up to the 60mm centre section once the oem cat is removed. Think ive got it covered
The Eibach Springs have arrived - so i can fit them to the OEM shocks and see a 25- 30mm drop all round or might possibly wait until i have a found a set of Koni Sports as they are a brilliant combo
1996-2000 1993 EG9 Blue Civic 1.6 Vti - Traded in against the BB4
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC
2000-2019 1994 2WS BB4 Milano Red JDM Prelude Si VTEC LSD
2015 on > 1991 4WS BB1 Phantom Pearl Grey JDM Prelude Si VTEC LSD
2021 ON > 1998 2WS BB6 White Pearl JDM Prelude Si VTEC