Page 1 of 25

Fefelarue's 3rd gen Honda Prelude

Posted: Wed May 01, 2013 11:28 pm
by fefelarue
Hey folks, my name is Felix. I used to drive a peugeot 106 quiksilver which looked like this:

Image
Image

But anyway, onto better things! Here's my new car...

It's a gen 3 1989 Honda Prelude 2.0i 16v 150bhp with 4 wheel steering :)

It's only got 81k on the clock, and it's pretty much immaculate inside and out.

I got a couple of quick snaps on the long drive back from picking it up:

Image
Image
Image


Then today I finally got some time to give it a clean, and start the free mods :)

First up was the numberplate. I hated the ugly numberplate mount it had, so did this..

Before:

Image

Mount removed:

Image

Cleaned:

Image

Then re-attached the plate a bit lower down without the surround:

Image


That's all the modding I had time for today, so I found a building site and took some pics:

Image
Image
Image
Image



Let me know what ya think :D

Re: Fefelarue's 3rd gen Honda Prelude

Posted: Wed May 01, 2013 11:29 pm
by fefelarue
So today I did some bits on the rear end.

I started on the smoothing :)

So after painstakingly removing the badges and glue residue, I was left with these rather unsightly holes:
Image

So off to halfords to get the filler, and I filled the drokk out of those holes:
Image

160 grit:
Image

800 grit wet:
Image

2000 grit wet:
Image

Then I just used high build primer and a touch up pen. This pic is before flatting and polishing:
Image

MEANWHILE.. I removed the number plate mount again and stuck the plate to the rear bumper..

Before:
Image

Removed:
Image

Final result for the day: I flatted down the brushed on paint and it looks like this:
Image
I didn't get time to do the centre badge today, so that'll have to wait for now...

I'll give it a proper polish and a blend in a couple of days when it's all rock solid, but even now you can't see where the holes were :)

Also, this is worth a watch. My mate attached his go-pro to the side of my car to get some 4 wheel steering action. And there's some nice exhaust sounds in there too! (this is with a completely standard exhaust):


As always, comments, opinions and suggestions welcome :)

Posted: Wed May 01, 2013 11:43 pm
by NafemanNathan
Another one to the ranks! :D Welcome to the club Felix :)

Love the vid 8)

Posted: Wed May 01, 2013 11:54 pm
by Doggo
That looks stunning, Felix. Great car! I would reaaally like that. Welcome in :D

Re: Fefelarue's 3rd gen Honda Prelude

Posted: Thu May 02, 2013 12:08 am
by fefelarue
Thanks for the welcome guys :D Looking forward to getting stuck in!

I'm sure i'll be asking you all for a lot of help and info in the coming months :P

Posted: Thu May 02, 2013 12:58 am
by honda-hardy
NICE CAR. i dont want to sell mine but i have too. :cry:

i couldnt tempt you with a jdm prelude inx boot spoiler? its in dark silver at the moment, but looking at your painting skills, i think you would cope.

Image

Image

Image

Image

the brake light is full length and very bright. £50 plus p+p. this will include a home made harness and instruction on where to run the loom.

Re: Fefelarue's 3rd gen Honda Prelude

Posted: Thu May 02, 2013 1:15 am
by fefelarue
Hey mate :) thanks for the offer, it's a bargain but it's a bit too ott for what i'm going for. I want to clean the entire rear end. I was considering a little stick-on boot lip spoiler but that's as far as i'd go i think. Nice car though, shame you're selling it!

Posted: Thu May 02, 2013 1:20 am
by honda-hardy
the other option is... i have a spare new old stock led bar. perhaps you could cut a groove in the lip of the boot and flush fit it in to the boot.

Image

Image

Re: Fefelarue's 3rd gen Honda Prelude

Posted: Thu May 02, 2013 1:38 am
by fefelarue
Haha, tempting! But i'm gonna pass at the moment thanks dude. Any other mods you're selling?

Posted: Thu May 02, 2013 1:56 am
by honda-hardy
only a standard spoiler in white. w/o brake light.