Page 1 of 2

Fuel Lines

Posted: Mon Feb 11, 2019 4:09 pm
by EddieMunster
Hi

I've just noticed my rear to front fuel line has had it, it's corroded at the union of the flexi-pipe on the rear beam.

Honda no longer stock them, so, what are the options for the quickest possible resolution? Do I make a new piece of pipe and disregard the rubber union the other side of the rear beam, as I'll guess that's on its way out too, or are there any off-the-shelf options?

Image

Regards

Fuel Lines

Posted: Mon Feb 11, 2019 7:14 pm
by vanzep
I will be fixing the leak in the main line at the union on my BB4 this week - depends where leaks is on your line but this info may help
see here for info:
viewtopic.php?f=17&t=1464
info on page 86
I bought some fuel line off ebay 8mm id - 15mm od and along with a 1/4BSP to 8mm barbed connector & some jubilee clamps
(about 6 quid in parts) :)

Fuel Lines

Posted: Mon Feb 11, 2019 7:54 pm
by EddieMunster
vanzep wrote:
Mon Feb 11, 2019 7:14 pm
I will be fixing the leak in the main line at the union on my BB4 this week - depends where leaks is on your line but this info may help
see here for info:
viewtopic.php?f=17&t=1464
info on page 86
I bought some fuel line off ebay 8mm id - 15mm od and along with a 1/4BSP to 8mm barbed connector & some jubilee clamps
(about 6 quid in parts) :)
Your repair is from the flexi-pipe up to the tank, my primary concern is from the fuel pipe at the union to the front of the car; it's so badly corroded that winding up that nut has pushed the pipe away from the join, as you can see in the picture. I suspect I'm just going to have to make a new rear-to-front pipe for it.

Fuel Lines

Posted: Mon Feb 11, 2019 9:18 pm
by vanzep
no mate - the repair im working on is to fix a leak in the pipe just underneath the fuel union on the hard line that goes to the front of the car.
i found the union can be seperated into two halves and the repair i am doing is to take away the bottom section of the union and fit a 1/4 BSP to 8MM barbed connector and then cut of the leaky/rusty section of line and use some new fuel hose and clips.
the pics i have shown are on a spare fuel tank thats off the car and just mocked up so i can figure out how to do the repair without having to remove the tank from the car ;)

Fuel Lines

Posted: Mon Feb 11, 2019 9:26 pm
by EddieMunster
vanzep wrote:
Mon Feb 11, 2019 9:18 pm
no mate - the repair im working on is to fix a leak in the pipe just underneath the fuel union on the hard line that goes to the front of the car.
i found the union can be seperated into two halves and the repair i am doing is to take away the bottom section of the union and fit a 1/4 BSP to 8MM barbed connector and then cut of the leaky/rusty section of line and use some new fuel hose and clips.
the pics i have shown are on a spare fuel tank thats off the car and just mocked up so i can figure out how to do the repair without having to remove the tank from the car ;)
You're going to create a union between the steel pipe and the flexi-union with rubber tubing running underneath the car? I doubt you'll get through an MOT with that, in fact I'm almost completely sure it won't.

Fuel Lines

Posted: Tue Feb 12, 2019 1:59 am
by vanzep
I dont agree - the oem pipe from the fuel pump to the union has a large rubber section in it - ok so its between the top and back of the fuel tank but proper rubber fuel pipe should be acceptable and there is a plastic cover that goes over the fuel line underneath the car so protects it from damage -also i dont think they remove any covers when carrying out an mot inspection :)

Fuel Lines

Posted: Tue Feb 12, 2019 7:38 am
by EddieMunster
vanzep wrote:
Tue Feb 12, 2019 1:59 am
I dont agree - the oem pipe from the fuel pump to the union has a large rubber section in it - ok so its between the top and back of the fuel tank but proper rubber fuel pipe should be acceptable and there is a plastic cover that goes over the fuel line underneath the car so protects it from damage -also i dont think they remove any covers when carrying out an mot inspection :)
I'd read your post as you using rubber pipe from the steel pipe, where the corrosion normally starts, to the front of the car, and that's definitely an MOT failure. From the rear beam backwards/upwards, it doesn't have to be covered, just secure and out of the way of moving parts.

Fuel Lines

Posted: Tue Feb 12, 2019 10:22 am
by vanzep
Ahhh no worries - im just putting in a small section of rubber fuel hose.
hope the info helps you out :)

Fuel Lines

Posted: Tue Feb 12, 2019 10:26 am
by EddieMunster
vanzep wrote:
Tue Feb 12, 2019 10:22 am
Ahhh no worries - im just putting in a small section of rubber fuel hose.
hope the info helps you out :)
Cheers....

I'm going to make a union from the steel pipe to the tank, in aeroquip or the like, as I suspect my rubber pipe will be perished as badly as the steel pipe. What was odd was that it literally only appeared yesterday, and within 30 mintues, without any tampering at all, it went from very slight fumes to heavy leak! Put an end to me doing the rear suspension/ABS sensor, although that'd already come to a halt as I'd been sent the wrong springs, bump stops and washers; I guess it pays to go directly to Honda sometimes.

Fuel Lines

Posted: Thu Feb 14, 2019 1:21 pm
by vanzep
ive given up trying to fix this myself :cry:
turns out the main leak is from the fuel return line which the garage repaired a couple of years ago and although i tried i just dont have clear access or the strength to push the hose far enough up the hard line to stop the leak :x
so its off to the garage tomorrow to see what they can do - ive taken all the lines off the spare tank i have so that they can replace all of them if needs be. ive drained the petrol out of the tank so hope there is enough fumes left for me to travel a mile or two.....

hope you have better luck fixing your leak :)