Congratulations to vtecmec for winning May/June's Lude Of The Month, with his DIY Turbo BB1 build.

>>> Click Here For Profile <<<

Image

Type S Intake

Engine/Gearbox questions and discussion
User avatar
ATR84
Posts: 974
Joined: Fri Jan 27, 2012 1:53 pm
My Generation: 5G
XBOX GamerTag: mike84n
Location: West Sussex
Has thanked: 47 times
Been thanked: 101 times

Type S Intake

Post by ATR84 » Thu May 30, 2019 11:17 am

I noticed the other day that the intake on my type s has a dent on it near where it gets close to the back of the battery. I assume this is not normal.

Will this be affecting performance, I assume yes. Are the AEM V2 and K&N Typhoon long arm good alternatives to the Type S intake?

https://www.amazon.co.uk/clouddrive/sha ... 6qEHqFHvx3

User avatar
Drax
Moderator
Posts: 6259
Joined: Wed Dec 22, 2010 4:05 pm
My Generation: 4G
Location: Wrexham, North Wales
Has thanked: 16 times
Been thanked: 373 times

Type S Intake

Post by Drax » Thu May 30, 2019 12:21 pm

Can you not take the intake off & appart then push the dent back out being it's plastic? i'd be keen to keep the type S intake as it's one of the best for a lude. your two alternatives are very good though, plus the CDA intakes :)
2.2 JDM DOHC SI-VTEC LSD TCS 4WS ABS BB1 MANUAL 1992
Image
FOR PAUL

User avatar
ATR84
Posts: 974
Joined: Fri Jan 27, 2012 1:53 pm
My Generation: 5G
XBOX GamerTag: mike84n
Location: West Sussex
Has thanked: 47 times
Been thanked: 101 times

Type S Intake

Post by ATR84 » Thu May 30, 2019 1:58 pm

Drax wrote:
Thu May 30, 2019 12:21 pm
Can you not take the intake off & appart then push the dent back out being it's plastic? i'd be keen to keep the type S intake as it's one of the best for a lude. your two alternatives are very good though, plus the CDA intakes :)
Do the sections of the Type S intake come apart? If so I might be able to get to it in order to push it out. If not I don't think I will be able to get to it........

Scott560
Posts: 1320
Joined: Sat Aug 31, 2013 4:44 pm
My Generation: 5G
Location: Didcot
Has thanked: 19 times
Been thanked: 214 times

Type S Intake

Post by Scott560 » Thu May 30, 2019 2:04 pm

The sections do come apart. i doubt the dent is affecting performance at all , so i wouldnt worry about it at all (feel free to push it back out though if possible).

You can always loosen the battery stay and move the battery as much as possible away from the intake and then re clamp it.
'00 UKDM 2.2VTI H22a8
'21 'e' Advance

User avatar
RattyMcClelland
Moderator
Posts: 9191
Joined: Wed Aug 04, 2010 10:02 pm
My Generation: 5G
PSN GamerTag: RattyMcClelland
Location: Leicestershire
Been thanked: 181 times

Type S Intake

Post by RattyMcClelland » Thu May 30, 2019 4:03 pm

Get photos up. Dent won't effect anything.
Image

User avatar
ATR84
Posts: 974
Joined: Fri Jan 27, 2012 1:53 pm
My Generation: 5G
XBOX GamerTag: mike84n
Location: West Sussex
Has thanked: 47 times
Been thanked: 101 times

Type S Intake

Post by ATR84 » Thu May 30, 2019 4:56 pm

RattyMcClelland wrote:
Thu May 30, 2019 4:03 pm
Get photos up. Dent won't effect anything.
Can you not see the link in the first post with the pic? I was going to upload to photobucket but they seem to have locked my account. Any other free accounts I could use?

User avatar
tom023
Supporter 2016
Posts: 521
Joined: Sun Mar 06, 2016 5:45 pm
My Generation: 5G
Location: Alicante Spain
Has thanked: 35 times
Been thanked: 20 times

Type S Intake

Post by tom023 » Thu May 30, 2019 5:05 pm

You will not notice any difference in performance taking that dent out, although I would still take it out. Unclip the top of the filter housing one end and undo the jubilee band fastener on the other end. Remove the whole piece and try warming the dented part of the plastic up slightly (hair dryer ? Really hot water? ) while pushing the dent out from the inside, either with your hand if you can or anything wide enough to get a decent purchase on the dent and to avoid puncturing the plastic.

I would keep hold of the typeS intake as it is one of the best due to its "dual chamber". Even so the aem v2 is considered just as good.

User avatar
NafemanNathan
LotM Winner
Posts: 20144
Joined: Sun Aug 08, 2010 9:37 pm
My Generation: 0G
Location: Yeovil, Somerset
Has thanked: 8 times
Been thanked: 121 times

Type S Intake

Post by NafemanNathan » Thu May 30, 2019 5:55 pm

That dent will be easy to get to. The neck of the air box lid connects right there (behind the battery). Release the 4 clips of the air box lid and simply pull it out of the pipe part. Then you'll see the inside of the dent :)

User avatar
RattyMcClelland
Moderator
Posts: 9191
Joined: Wed Aug 04, 2010 10:02 pm
My Generation: 5G
PSN GamerTag: RattyMcClelland
Location: Leicestershire
Been thanked: 181 times

Type S Intake

Post by RattyMcClelland » Thu May 30, 2019 5:56 pm

Oops I didn't see that.

That dent is standard and yes I'm being serious, mine had it when I have type s intake.
Image

newkid
Supporter 2016
Posts: 2665
Joined: Thu Feb 23, 2012 8:28 pm
My Generation: 4G
PSN GamerTag: spaz_ma_taz
Location: Edinburgh
Has thanked: 13 times
Been thanked: 50 times

Type S Intake

Post by newkid » Thu May 30, 2019 6:09 pm

RattyMcClelland wrote:
Thu May 30, 2019 5:56 pm
Oops I didn't see that.

That dent is standard and yes I'm being serious, mine had it when I have type s intake.
Spot on.

Post Reply

Return to “Engine / GearBox”