Congratulations to vtecmec for winning May/June's Lude Of The Month, with his DIY Turbo BB1 build.
>>> Click Here For Profile <<<
>>> Click Here For Profile <<<
Rear shock absorber mounting & spring mounting
- CARRisma
- Posts: 892
- Joined: Tue May 01, 2012 11:30 am
- My Generation: 5G
- Location: Horley, Surrey
- Has thanked: 17 times
- Been thanked: 27 times
- Contact:
Rear shock absorber mounting & spring mounting
Over the last few months, the rear of my car has become very creaky. Sounds high up to me. I suspect it’s related to worn rear shock absorber mounting (52675-SS0-004) and / or rear spring mountings (52686-SS0-004). Both highlghted in red below:
Back in 2014, may car had a full set of polyurethane bushes fitted. A month or so ago, I had a poke around underneath the car but couldn’t see anything wrong. ARB seems solid. I haven’t yet had a look at the above mentioned parts, but I hope / guess they're simple ish to replace? Jack up car, undo some bolts at the top from within the boot, drop down suspension and then replace the parts. Has anyone done here this before? Any tips?
Back in 2014, may car had a full set of polyurethane bushes fitted. A month or so ago, I had a poke around underneath the car but couldn’t see anything wrong. ARB seems solid. I haven’t yet had a look at the above mentioned parts, but I hope / guess they're simple ish to replace? Jack up car, undo some bolts at the top from within the boot, drop down suspension and then replace the parts. Has anyone done here this before? Any tips?
2000 Honda Prelude 2.2 VTi (H22A8 / BB8).
- tom023
- Supporter 2016
- Posts: 521
- Joined: Sun Mar 06, 2016 5:45 pm
- My Generation: 5G
- Location: Alicante Spain
- Has thanked: 35 times
- Been thanked: 20 times
Have you checked your poly bushes are greased enough and moving? It's something quick to check off before purchasing new parts.
To replace the top mounts you need to completely remove the shock and spring combo from the car and compress the spring with spring compression tools so that you can undo the top mounts to replace them. After fitting the new ones, slowly release the compression tools to fit the road spring back into place.
To replace the top mounts you need to completely remove the shock and spring combo from the car and compress the spring with spring compression tools so that you can undo the top mounts to replace them. After fitting the new ones, slowly release the compression tools to fit the road spring back into place.
- wurlycorner
- Ye are glad to be dead, RIGHT?
- Posts: 21217
- Joined: Sat May 19, 2012 3:33 pm
- My Generation: 4G
- Location: Chelmsford, Essex
- Has thanked: 1958 times
- Been thanked: 239 times
-
- Posts: 1325
- Joined: Sat Aug 31, 2013 4:44 pm
- My Generation: 5G
- Location: Didcot
- Has thanked: 19 times
- Been thanked: 214 times
Re: Rear shock absorber mounting & spring mounting
I don't think these normally come with a set of Polly bushes.
I did see item 13 available separately on strongflex website I think.
These bushes are known to wear out, causing the rear shock generally to knock usually...
Sent from my MIX using Tapatalk
I did see item 13 available separately on strongflex website I think.
These bushes are known to wear out, causing the rear shock generally to knock usually...
Sent from my MIX using Tapatalk
'00 UKDM 2.2VTI H22a8
'21 'e' Advance
'21 'e' Advance
-
- Posts: 1325
- Joined: Sat Aug 31, 2013 4:44 pm
- My Generation: 5G
- Location: Didcot
- Has thanked: 19 times
- Been thanked: 214 times
Re: Rear shock absorber mounting & spring mounting
Doesn't take too long to remove the rear struts.
Remove the inner boot liner.
Undo 2x 14mm top strut nuts.
Undo 2x 17mm upper suspension arm nuts.
undo 1x 17m lower strut mounting bolt.
Upper arm will then come free from chassis and it can be lowered, strut can then be manipulated out of place.
Dismantling the strut (removing the top hat) is dangerous as you'd need to compress the spring.
Best do the removal yourself and then take the struts to a small garage to get the springs done and loosened. They can do the collar/bush for you for practically no time taken at all.
You can grease the upper arm bushes easily. If you want to do this, loosen the 2x 14mm bolts and they will come free of the arms. Might need some persausion so perhaps mount the upper mounts back to he chassis again. With no strut in the way it will be easy to undo the bolts. It's hard to do once they are disconnected.
Sent from my MIX using Tapatalk
Remove the inner boot liner.
Undo 2x 14mm top strut nuts.
Undo 2x 17mm upper suspension arm nuts.
undo 1x 17m lower strut mounting bolt.
Upper arm will then come free from chassis and it can be lowered, strut can then be manipulated out of place.
Dismantling the strut (removing the top hat) is dangerous as you'd need to compress the spring.
Best do the removal yourself and then take the struts to a small garage to get the springs done and loosened. They can do the collar/bush for you for practically no time taken at all.
You can grease the upper arm bushes easily. If you want to do this, loosen the 2x 14mm bolts and they will come free of the arms. Might need some persausion so perhaps mount the upper mounts back to he chassis again. With no strut in the way it will be easy to undo the bolts. It's hard to do once they are disconnected.
Sent from my MIX using Tapatalk
'00 UKDM 2.2VTI H22a8
'21 'e' Advance
'21 'e' Advance
- CARRisma
- Posts: 892
- Joined: Tue May 01, 2012 11:30 am
- My Generation: 5G
- Location: Horley, Surrey
- Has thanked: 17 times
- Been thanked: 27 times
- Contact:
So, on Sunday I drove over 50 miles in the rain, mostly motorway. The next day, my suspension creaks had completely disappeared! Silent, apart from the usual banging & crashing. Was also OK over 135 miles of driving yesterday. But the creaking is starting to come back slightly today.
2000 Honda Prelude 2.2 VTi (H22A8 / BB8).
-
- Posts: 1325
- Joined: Sat Aug 31, 2013 4:44 pm
- My Generation: 5G
- Location: Didcot
- Has thanked: 19 times
- Been thanked: 214 times
Re: Rear shock absorber mounting & spring mounting
How about a quick spray of gt85 or silicon spray, should eventually trickle into the rubbing part?
Sent from my MIX using Tapatalk
Sent from my MIX using Tapatalk
'00 UKDM 2.2VTI H22a8
'21 'e' Advance
'21 'e' Advance
- CARRisma
- Posts: 892
- Joined: Tue May 01, 2012 11:30 am
- My Generation: 5G
- Location: Horley, Surrey
- Has thanked: 17 times
- Been thanked: 27 times
- Contact:
I am considering that as a quick fix but think that would only be temporary. This is an interesting read:Scott560 wrote:How about a quick spray of gt85 or silicon spray, should eventually trickle into the rubbing part?
Sent from my MIX using Tapatalk
https://www.suspension.com/blog/the-bes ... -bushings/
2000 Honda Prelude 2.2 VTi (H22A8 / BB8).