Page 2 of 3

Wheel refurbishment

Posted: Thu Jul 11, 2019 9:24 pm
by Scott560
taken a while, but wheels and centre caps all etch primed, primed and sanded down, front and back, very smooth all over now... will get some pictures up.

Silver should be going on this weekend and the clear coat perhaps? Not sure if you have to wait a long while for the 1k base coat to cure before sealing it in with 2k lacquer? Don't know if the silver solvent needs thinnig 10% or not?

Anyways, struggling to find info on prelude tyre sizes for the 17s. I believe there are 2 sizes of the Motegi 17inch hairpins?

The ones i have are 17x7 , enkei brand, offset 55. Cant find anything in the manual regarding optional sizes, cant find consistent information online, and the lings parts page is down ( https://www.lingshondaparts.com/partsca ... f/B__1800/ ).

I've seen varying sizes from 205/45/17 , 215/40/17 (seems the most correct for 17x7) , and 225/40/17 for the 17x7.5 (are these accord type R wheels?).

Wheel refurbishment

Posted: Fri Jul 12, 2019 7:38 am
by RattyMcClelland
Thin the base coat if you need to. Thats your call. I like my paint to be slightly thicker than beer and i heat it up in the gun.
Do as many coats as you need but allow flash off time between coats.
You should lacquer soon after. Give ot 10-15mins of drying between base and lacquer.

Tyres size. 205/45/17 or the better 215/45/17.

Wheel refurbishment - Now with pics

Posted: Sat Jul 13, 2019 9:38 pm
by Scott560
To try and keep bits off, gazebo went up - not sure if it helped or not
Image



2k etch primer on - went on very thin and watery, but dried/set much better with very little run or problems... Wheels had been sandblasted and had a texture of pumice stone.
Image



Some of the runs - looked worse than it was - the etch primer was very thin, and i used a cheap spray gun which had a far too big a nozzle (1.5mm)
Image



Aldi half price bicycle stand and piece of wood - not ideal but better than nothing. This is the high build 2k primer going on. Some areas were very coarse and like pumice stone, some places not as bad - turns out i'm not a paint sprayer... I think the trick is to try and apply a nice continous stream of paint. I was probably being to delicate , depositing far too little paint over a long period of time. This gave me much more work to do when sanding it down...
Image



Don't leave the gazebo up in the wind - came back from work one day to find it 3m further down the garden. No damage to the wheels or gazebo or garden thankfully.
Image



With the aid of a lazy susan and some celebration tubs, wheels and center caps were painted in pairs today, using the wheelpaints.co.uk 1k solvent based Honda standard silver. I had to thin it down 20% thinners as it was quite thick. Decided to paint them in pairs (rather than 1 at a time or 4 in one go) so that any colour mismatch I could put on either side of the car. Didn't know how much paint to mix, so mixed up 2 pots for 2 separate sessions as I also didn't have enough space to store/move/manipulate the wheels to paint the face and the back at the same time. Strangely, the paint even when thoroughly stirred, exhibited a black film/streak on the surface. This persisted despite thorough shaking, and even when thinned in the cup, and then when in the gun. There were times when the gun was depositing inconsistent colour. One centre cap had to have a going over again, but the wheels in the most all dried to be near identical colour...
Image



Annoyed I missed some filling/prep on the area of damage by the spoke at the bottom, I spent hours doing it so no idea how i missed that bit! I have the Honda logos, but they have paint on from a previous owner, so they need some very high grade wet sandpaper to remove the old over spray before I stick them back to the centre caps. This wheel came out near perfect otherwise...
Image



And this one, you can make out some slight pitting in the primer (on the inside of the spoke) which couldn't be removed by sanding before painting. I can only assume when i applied the primer i didn't do a thick enough coat, or it didn't mix/apply well. It was smooth to the touch, but its not that noticeable. When fitted and moving, no one will notice it (but ill still be annoyed its there!)
Image



From afar they look 100%
Image



The first pair came out great, but the second pair I seemed to screw up more on - perhaps I accidentally adjusted the gun (now I see why they have gun stands as a thing!). Some larger runs on this one. I'm hoping the paint will harden up and i can remove some of it by light sanding with high grade paper tomorrow before lacquering.
Image



some more runs visible here, also some roughness in between the spokes where I was too harsh in my removal of old paint (in the same way the paint gun struggles to get paint in the crevice, so too must have the sand blaster).
Image


All in all they will come out looking OK, but not show room quality, not up to OE spec... I'm not sure what you'd get for £50/wheel at a refurb place, but probably a slightly better job than this , and in my eyes probably worth it. Whilst there is some merit in learning and trying, at the end of the day i'm down a good chunk of hours and probably a couple of hundred quid.

Makes me question whether i have the patience to repaint the damaged Motegi kit i picked up , or leave it to the experts...

Also if anyone has a single ATR wheel nut let me know, i only seem to have 19 of the low profile ones (and the original 16inch wheel ones are too long to fit under the centre caps).

Wheel refurbishment - Now with pics

Posted: Sat Jul 13, 2019 9:46 pm
by Andyjess666
If you got a photo of the wheel nut you need oosy likey have one mate yours for free

Wheel refurbishment - Now with pics

Posted: Sat Jul 13, 2019 10:10 pm
by RattyMcClelland
Good effort i say.
I do smart repairs as a business and i dont do wheels, i dont have the patience for them and plus id need to charge £140+vat to make money off one compared to the time against a bumper scuff.
Trust me. Good effort. Definately lacquer them in the morning or else they will delaminate quickly.

Wheel refurbishment - Now with pics

Posted: Sat Jul 13, 2019 10:21 pm
by toadster
Lo :D
Fantastic job matey :mrgreen:
I wouldn't even attempt it myself so rep to You :clap:
Cheers ;)
Toadster

Wheel refurbishment - Now with pics

Posted: Mon Jul 15, 2019 9:01 pm
by Scott560
wheels nuts look like this:

http://ww.scottwoodcock.co.uk/IMG_20190715_201129.jpg

if anyone has one let me know :)

Wheel refurbishment - Now with pics

Posted: Tue Jul 16, 2019 6:40 am
by norks27
RattyMcClelland wrote:
Sat Jul 13, 2019 10:10 pm
I do smart repairs as a business and i dont do wheels, i dont have the patience for them and plus id need to charge £140+vat
The smart repair chap I use says the exact same thing.

@Scott560 Nice Job :thumbup:

Wheel refurbishment - Now with pics

Posted: Tue Jul 16, 2019 10:07 am
by sol-lude
awesome work here mate keep it up.

Wheel refurbishment - Now with pics

Posted: Thu Jul 18, 2019 6:21 pm
by vtijon
I bought my 1999 car in 2001 with 9000 miles. All tyres were Yokohama 205/45/17 which must have been on since new. The wheels are like yours 17 x 7. However a sticker on the drivers doorpost says 215/45/17 and so did the Honda sales brochure. Therefore after the original Yokohama's I've used 215/45/17.