Page 1 of 2
Motegi rear lip
Posted: Mon Jan 27, 2020 8:55 am
by Scott560
Is their a trick to getting this to fit better?
The front one, even though a copy, fitted like a glove.
The rear fits OK at the sides, there is no gap at all, bumper and lip are flush in this area.
However, at the rear, around the number plate area, the lip is quite pronounced outwards, and there is more than a 1 or 2 mm gap (more like 3 or 4). You can't really see it unless you close, but its annoying none the less.
I cant quite see whats gone wrong, the captive nut clip things are all on and snug, and each 10mm shouldered bolt is done up whilst pushing the lip into place.
Will need to wait for my legs/thighs/arse to recover first - ache all over from the repeated getting up/down.
Motegi rear lip
Posted: Mon Jan 27, 2020 5:15 pm
by RattyMcClelland
Mine is flush-ish on the back but sides there is a gap.
Spent an hour rejigging it but only fits one way.
Motegi rear lip
Posted: Tue Jan 28, 2020 1:15 am
by newkid
Did you leave the standard lip on?
Motegi rear lip
Posted: Tue Jan 28, 2020 11:20 pm
by Scott560
newkid wrote: ↑Tue Jan 28, 2020 1:15 am
Did you leave the standard lip on?
No lol! Now I've cleaned the car it's less noticeable, just slightly annoying.
Will have to do a mini photo shoot, car is looking half decent now. Really changes the look of the car (motegi kit plus the wheels)
I'll leave it be for risk of making it worse
Motegi rear lip
Posted: Fri Jan 31, 2020 7:39 am
by newkid
See from memory the standard lip stays on and helps shape it properly.
Motegi rear lip
Posted: Fri Jan 31, 2020 6:57 pm
by Scott560
newkid wrote: ↑Fri Jan 31, 2020 7:39 am
See from memory the standard lip stays on and helps shape it properly.
really? can anyone else verify?
Motegi rear lip
Posted: Fri Jan 31, 2020 11:11 pm
by RattyMcClelland
No way would my motegi lip fit over the standard lip. They use the same identical mounting points and slide in clip in points. The slide in points are only thick enough for one lip....ie a few millimetres gap.
Motegi rear lip
Posted: Fri Jan 31, 2020 11:40 pm
by Lankysod07
RattyMcClelland wrote: ↑Fri Jan 31, 2020 11:11 pm
No way would my motegi lip fit over the standard lip. They use the same identical mounting points and slide in clip in points. The slide in points are only thick enough for one lip....ie a few millimetres gap.
Yep 100% Motegi lip follows the same mounting points as the standard lip. You can install the Motegi lip over the standard bud.
Motegi rear lip
Posted: Fri Jan 31, 2020 11:52 pm
by RattyMcClelland
Lankysod07 wrote: ↑Fri Jan 31, 2020 11:40 pm
RattyMcClelland wrote: ↑Fri Jan 31, 2020 11:11 pm
No way would my motegi lip fit over the standard lip. They use the same identical mounting points and slide in clip in points. The slide in points are only thick enough for one lip....ie a few millimetres gap.
Yep 100% Motegi lip follows the same mounting points as the standard lip. You can install the Motegi lip over the standard bud.
My point was it wont. One won't fit over the other. Mine wouldn't. I had to remove the standard lip to fit the motegi. Fitting the standard lip behind the motegi fits no purpose as its totally hidden.
Motegi rear lip
Posted: Sat Feb 01, 2020 11:07 am
by Scott560
I think Lankysod meant to say 'can't' instead of can
- It wouldn't make sense for honda to fit the lip on top of the other (costs/effort) , same with sideskirts, they replace the original.
Actually now you mention the locating tabs/slots (about 1.5 inches wide, 2mm thick plastic tab protruding from skirt, slot in bumper just under the number plate holder) - there is no way the Motegi lip could fit over the existing one (not unless it was butchered)
Still loving the transformation, the motegi kit, refurbed 17s with the low profile tyres, it really is a big difference!