I want to make my Mugen header more shiny.
I had a go with autosol on Sunday, while it improved it, it didn't do a lot in the grand scheme of things. Is there anything else I can do myself or does it need to come off and go to a specialist of some kind?
I don't want to heat wrap it really.
Congratulations to vtecmec for winning May/June's Lude Of The Month, with his DIY Turbo BB1 build.
>>> Click Here For Profile <<<
>>> Click Here For Profile <<<
Header polishing
- RattyMcClelland
- Moderator
- Posts: 9196
- Joined: Wed Aug 04, 2010 10:02 pm
- My Generation: 5G
- PSN GamerTag: RattyMcClelland
- Location: Leicestershire
- Been thanked: 185 times
Header polishing
You can polish it with a full menzera metal polish kit on a drill but after a few heat cycles it will be discoloured again as that's the nature of high heat and polished stainless steel.
https://www.thepolishingshop.co.uk/budg ... l%20polish
https://www.thepolishingshop.co.uk/budg ... l%20polish
- ATR84
- Posts: 975
- Joined: Fri Jan 27, 2012 1:53 pm
- My Generation: 5G
- XBOX GamerTag: mike84n
- Location: West Sussex
- Has thanked: 48 times
- Been thanked: 102 times
Header polishing
Yeah but that Mugen header has probably been on the car for most of it's life, if I kept on top of it and just went over it with autosol every so often it would probably be ok? My main issue is getting it to the clean/polished stage. Thanks for the link, I will consider that as an option.
What about ceramic coating?
What about ceramic coating?
- RattyMcClelland
- Moderator
- Posts: 9196
- Joined: Wed Aug 04, 2010 10:02 pm
- My Generation: 5G
- PSN GamerTag: RattyMcClelland
- Location: Leicestershire
- Been thanked: 185 times
Header polishing
Well consider my shiney polished hytech stainless header went on my lude and it was dull brown by the time I went home from performance autoworks where fitted to Leicester.
Try Zircotec for a ceramic coating. It's around £400 for a 2 piece header, they had mine for 4 weeks and didn't touch it. I got them to send it back as PAW needed it. Useless but apparently good.
Try Zircotec for a ceramic coating. It's around £400 for a 2 piece header, they had mine for 4 weeks and didn't touch it. I got them to send it back as PAW needed it. Useless but apparently good.
- ATR84
- Posts: 975
- Joined: Fri Jan 27, 2012 1:53 pm
- My Generation: 5G
- XBOX GamerTag: mike84n
- Location: West Sussex
- Has thanked: 48 times
- Been thanked: 102 times
Header polishing
Well they lost £400 of business for being slow, maybe they don't need the money
There are some local companies to me that offer this service, so might give it a go.
Is removing the header an easy DIY job or do I need a ramp etc? It looks like I can just get it out via the engine bay........
There are some local companies to me that offer this service, so might give it a go.
Is removing the header an easy DIY job or do I need a ramp etc? It looks like I can just get it out via the engine bay........
-
- Posts: 1338
- Joined: Sat Aug 31, 2013 4:44 pm
- My Generation: 5G
- Location: Didcot
- Has thanked: 19 times
- Been thanked: 221 times
Header polishing
I wouldn't run the risk of trying to remove it yourself. Exhaust bolts are always a PITA, and you may be unlucky enough for a stud to snap or bolt get mangled.
You would need to jack the front of the car up, the get to the bolts where the header meets the downpipe. You would also need to replace the gaskets ideally which might be hard to get hold of?
For a purely cosmetic procedure , i would leave it in place.
You would need to jack the front of the car up, the get to the bolts where the header meets the downpipe. You would also need to replace the gaskets ideally which might be hard to get hold of?
For a purely cosmetic procedure , i would leave it in place.
'00 UKDM 2.2VTI H22a8
'21 'e' Advance
'21 'e' Advance
- ATR84
- Posts: 975
- Joined: Fri Jan 27, 2012 1:53 pm
- My Generation: 5G
- XBOX GamerTag: mike84n
- Location: West Sussex
- Has thanked: 48 times
- Been thanked: 102 times
Header polishing
Good point Scott. I think I would prefer just to polish what is visible when you open the bonnet, I found this guide, thoughts on this method? I could do this with it in situ, yes I won't be able to get to all of it, but to the bits you can easily see I would.
https://honda-tech.com/forums/honda-acu ... 439/page3/
https://honda-tech.com/forums/honda-acu ... 439/page3/
-
- Posts: 1338
- Joined: Sat Aug 31, 2013 4:44 pm
- My Generation: 5G
- Location: Didcot
- Has thanked: 19 times
- Been thanked: 221 times
Header polishing
I've never tried polishing my exhaust so couldn't comment much on that front. doing it by hand on the car will be hard work - you probably want to get some kind of mechanised method on the go, but space is limited.
'00 UKDM 2.2VTI H22a8
'21 'e' Advance
'21 'e' Advance