Polybushing 5th Gen Prelude will 4th Gen fit?

[SiR Si]

Hi guys,

I need to replace the front tie bar bushes on my 5th gen and after being out in Nitin's polybushed up handling weapon of a type s, I figured that I may as well go polyurethane for the bush and while I am at it, I may as well poly bush up as much of the front end as I can afford.

So couple of questions, first the SuperFlex bushes are only listed for 4th Gen, I'm fairly sure that the majority of the bushes are the same, but has anyone done this on a 5th gen?

The bush I 100% need is this one:
http://www.superflex.co.uk/proddetail.p ... F192-2129K


But I was thinking of fitting these, if they will go on the 5th gen:
http://www.superflex.co.uk/proddetail.p ... 92-2061KSS

http://www.superflex.co.uk/proddetail.p ... F192-2131K

http://www.superflex.co.uk/proddetail.p ... F192-0265K

http://www.superflex.co.uk/proddetail.p ... 92-0904-8K


This set is looking a little pricey, so does anyone have any idea what the best 'bang-for-buck' areas that should be polybushed first is so I can maybe just focus there for the moment...

Si

[Lude-dude]

is this for a type s?

if so you want the Type SH kit, non SH kit for 2ws

and think 4ws uses a mix of the 4th and 5th gen kits not 100%

[nitin_s1]

LudeDude, this is for his Sir which is is equivalent of a Base. He had a go in my Type-S.

[Merlin]

Those seem pricey compared to the ES bits IMO. For example I got the Energy Suspension graphite impregnated tie bar (radius rod in English ) bushes and ARB drop link bushes from the US for £36 delivered.

I think the US 5G Base is the same as the 92-96 Prelude.

Any reason to do just the front? The rear would be all over the place in comparison

[SiR Si]

Yeah as Nitin said this is for my SIR with 4ws, I went out in his Type S and was very impressed with the feel. Nitin you'll be interested to know I took my car out down that same 'lane' where we went and your S is in a different league to my SIR!.....

Just looking at the front at the moment because the OEM front tie bar is knackerd so looking at what I could replace while I change that. I'd see how the front goes and then look at doing the back..

[nitin_s1]

Good to know my Type-S keeps up in the bends with your Turbo'd prelude. sooo happy and smug.

[Merlin]

I totalled the cost of SuperFlex bushes you listed and It came to £161.25 The ES equivalents are £58.88 ($95.34) before delivery. Delivery from the US would be around $30 I would think.

Radius rod set - http://www.energysuspensionparts.com/pr ... prod=81202

Upper arms - http://www.energysuspensionparts.com/pr ... od=16.3106

Lower arms - http://www.energysuspensionparts.com/pr ... od=16.8106

ARB - http://www.energysuspensionparts.com/pr ... od=16.5123

On top of the bits you have listed its possible to replace the coil isolators and bumpstops in your coilovers.


Or you can buy the Master kit for $161 (£99.50) and get both the front an rear done. You'd need the trailing arm kit as well.
http://www.energysuspensionparts.com/pr ... d=16.18106

[Duo]

On a side note do be prepared to pay import tax if they catch the delivery, sometimes you get away with it but sometimes you get stung for it. Best to make sure you have a few extra quid you might need just in case

[Merlin]

Import tax is at the same rate as VAT (which I can't rember 17% or 20%), even still you'll be far under the cost of the SuperFlex.

[SiR Si]

That is all very cool indeed, I'm defiantly going to do that, much better value for money.

Just looking at the Upper arm details
http://www.energysuspensionparts.com/pr ... od=16.3106#
that seems to actually be upper and lower......

2 - 2294 Lower Control Arm Bushings
2 - 3289 Spacer Bushings for 2294
2 - Center Metal Sleeves for 2294, 3289
8 - 2280 Upper Control Arm Bushing Halves
4 - Center Metal Sleeves for 2280
1 - Small Formula 5 Prelube Tub
1 - Installation Instructions # 17152

If that is the case not too sure where this one goes?
http://www.energysuspensionparts.com/pr ... od=16.8106