Congratulations to vtecmec for winning May/June's Lude Of The Month, with his DIY Turbo BB1 build.
>>> Click Here For Profile <<<
>>> Click Here For Profile <<<
No VTEC and car "splutters" and cuts out violently over 4k
- Drax
- Moderator
- Posts: 6280
- Joined: Wed Dec 22, 2010 4:05 pm
- My Generation: 4G
- Location: Wrexham, North Wales
- Has thanked: 21 times
- Been thanked: 394 times
No VTEC and car "splutters" and cuts out violently over 4k
Wills lude having problems again ...
As titled, but the cut out is just of power like the 112 mph limit.
He has checked the oil and coolant level, and we cleaned the VTEC solenoid a few months ago so I don't think it's that.
Could be the timing? Dizzy maybe? Even though that was swapped only a few months ago too.
I suspect it may even be the tps playing up, I will check Sunday this weekend. I'll also check spark plugs.
Any other suggestions welcome. Thank you!
As titled, but the cut out is just of power like the 112 mph limit.
He has checked the oil and coolant level, and we cleaned the VTEC solenoid a few months ago so I don't think it's that.
Could be the timing? Dizzy maybe? Even though that was swapped only a few months ago too.
I suspect it may even be the tps playing up, I will check Sunday this weekend. I'll also check spark plugs.
Any other suggestions welcome. Thank you!
2.2 JDM DOHC SI-VTEC LSD TCS 4WS ABS BB1 MANUAL 1992
FOR PAUL
FOR PAUL
- NafemanNathan
- LotM Winner
- Posts: 20144
- Joined: Sun Aug 08, 2010 9:37 pm
- My Generation: 0G
- Location: Yeovil, Somerset
- Has thanked: 8 times
- Been thanked: 122 times
More likely to be the dizzy again than any of the other things you've suggested.
When does his vtec normally cut in? As you say it's doing it over 4k revs, but obviously vtec normally doesn't kick in until 5.2k ish.
And when you say it's cutting out, is the engine stopping completely or are the revs just dropping (like a rev limiter)? And if cutting out completely is it automatically restarting?
Also I'm beginning to think this Will fella is a figment of your imagination
When does his vtec normally cut in? As you say it's doing it over 4k revs, but obviously vtec normally doesn't kick in until 5.2k ish.
And when you say it's cutting out, is the engine stopping completely or are the revs just dropping (like a rev limiter)? And if cutting out completely is it automatically restarting?
Also I'm beginning to think this Will fella is a figment of your imagination
-
- Posts: 468
- Joined: Tue Jul 16, 2013 8:33 pm
- My Generation: 5G
- Location: Portsmouth
- JEBB4
- Supporter 2014
- Posts: 1238
- Joined: Tue Feb 18, 2014 7:28 pm
- My Generation: 5G
- Location: Australia
- Has thanked: 85 times
- Been thanked: 73 times
Fuel pump on its way out? Not a common fault but thinking outside the box
My BB6 buildJamie P 2013 wrote:i like tits
viewtopic.php?f=17&t=54187
My BB2 build (yang)(WRITTEN OFF AND SOLD)
viewtopic.php?f=17&t=18866
My BB4 build (yin) (SOLD TO DRAX)
viewtopic.php?f=17&t=12087&hilit=JEBB4+ ... ty#p203321
- Drax
- Moderator
- Posts: 6280
- Joined: Wed Dec 22, 2010 4:05 pm
- My Generation: 4G
- Location: Wrexham, North Wales
- Has thanked: 21 times
- Been thanked: 394 times
I'll ask him about the fuel now..ATR84 wrote:My previous lude did this a few times and then stopped doing it. I put it down to dodgy fuel, as after it happened I stuck v power in every time rather than every other time and it didn't do it again.
the normal 5.2, we haven't fitted his spoon copy chip yet. It cuts power/revs like when you hit the 112mph JDM limiter, engine does not cut out altogether.NafemanNathan wrote:More likely to be the dizzy again than any of the other things you've suggested.
When does his vtec normally cut in? As you say it's doing it over 4k revs, but obviously vtec normally doesn't kick in until 5.2k ish.
And when you say it's cutting out, is the engine stopping completely or are the revs just dropping (like a rev limiter)? And if cutting out completely is it automatically restarting?
Also I'm beginning to think this Will fella is a figment of your imagination
If he is a figment of my imagination, then that's fine with me as I'll have a free lude then
don't think so but I'll checkTherealjj91 wrote:Does his rev meter jump about? When my dizzy bolts vibrated themselves loose my revs where all over the place and my car would splutter and not engage vtec.
could be, I have my old one as a spare so it could be swapped to eliminate that optionJEBB4 wrote:Fuel pump on its way out? Not a common fault but thinking outside the box
2.2 JDM DOHC SI-VTEC LSD TCS 4WS ABS BB1 MANUAL 1992
FOR PAUL
FOR PAUL
- 4thgenphil
- Supporter 2016
- Posts: 6660
- Joined: Tue Aug 03, 2010 4:15 pm
- My Generation: 4G
- Location: filming two girls one cup 2
- Has thanked: 5 times
- Been thanked: 27 times
- Drax
- Moderator
- Posts: 6280
- Joined: Wed Dec 22, 2010 4:05 pm
- My Generation: 4G
- Location: Wrexham, North Wales
- Has thanked: 21 times
- Been thanked: 394 times
This problem is still apparent. took it to Bri last night and we checked the timing and it was pretty much bob on.
still got 2 error codes appearing when the problem happens, 7 and 20 which is TPS and ELD.
i swapped the TPS for a spare a few days ago so i dont think its that at fault. does the TPS need to be adjusted sometimes? once you place it on the TB, when doing up the bolts there is room for adjustment up or down.... ?
EDIT - forgot to add, now ive been in Will's car when it happens, the splutter and cut out are the same thing, its just a splutter and cuts the power (doesnt stall the car) briefly for a second more than anything.
it also now seems to vtec ok
still got 2 error codes appearing when the problem happens, 7 and 20 which is TPS and ELD.
i swapped the TPS for a spare a few days ago so i dont think its that at fault. does the TPS need to be adjusted sometimes? once you place it on the TB, when doing up the bolts there is room for adjustment up or down.... ?
EDIT - forgot to add, now ive been in Will's car when it happens, the splutter and cut out are the same thing, its just a splutter and cuts the power (doesnt stall the car) briefly for a second more than anything.
it also now seems to vtec ok
Last edited by Drax on Thu Dec 15, 2016 2:31 pm, edited 1 time in total.
2.2 JDM DOHC SI-VTEC LSD TCS 4WS ABS BB1 MANUAL 1992
FOR PAUL
FOR PAUL
-
- Posts: 607
- Joined: Sun Jan 31, 2016 6:11 pm
- My Generation: 5G
- Been thanked: 7 times
Im adding another dimension to this Drax - could be the ignition switch that's not making contact properly?
Ranj
Ranj
I came before the chicken.. The argument is now settled!!
H22A8 197 motor with 190k on the clock
Tanabe lowering springs.
Skunk 2 megapower exhaust with a decat
M2B4 LSD Gearbox
Lightened flywheel
S2000 Steering Wheel
Type S Door inserts in Red
H22A8 197 motor with 190k on the clock
Tanabe lowering springs.
Skunk 2 megapower exhaust with a decat
M2B4 LSD Gearbox
Lightened flywheel
S2000 Steering Wheel
Type S Door inserts in Red
- Drax
- Moderator
- Posts: 6280
- Joined: Wed Dec 22, 2010 4:05 pm
- My Generation: 4G
- Location: Wrexham, North Wales
- Has thanked: 21 times
- Been thanked: 394 times
i doubt it mate, ignition switch problems are usually the engine cutting out or not starting at all, cheers for the input thoughFree Ranj Egg wrote:Im adding another dimension to this Drax - could be the ignition switch that's not making contact properly?
Ranj
2.2 JDM DOHC SI-VTEC LSD TCS 4WS ABS BB1 MANUAL 1992
FOR PAUL
FOR PAUL