Prelude Plans 2014

[NafemanNathan]

See plans for 2013.

[honda-hardy]

1, fit rear brake pads.
2, fit hel braided brake lines.
3, fit jdm rear bumper.
4, fit mugen rear spats.
5, fit wings west side skirts.
6, fit wings west front lip.
7, remove the cable ties from the boot torsion springs and join the group buy.
8, re seat vent behind rear bumper as this is where slight damp gets in.
9, under-seal the fantastic condition sills.
10, find a bloody type s seat in better condition than mine.
11....... tbc

[W1ggz]

Black BB4

1. Get body work sorted hopefully July although still trying to find the right person to do it.
2. Bronze window tint

GreyBB4

1: strip down suspension and polybush ( need to buy)
2: fit 5 stud conversion (in garage)
3: fit ATR front brake setup (in garage)
4: fit ATR inlet mani (in garage)
5: fit type S cams ( buying today off newkid)
6: fit re programable ecu and get rolling road set up done. ( have the ecu already)
7: buy some track tyres
8: fit new seats ( need to collect from rob)
9: finish stripping PAS out
10: get on track

[nucleustylzlude]

Mm...where to start?

1. Fit ALOT of parts: SEE HERE - list on first post
2. Get the car on the road
3. Get the car on track
4. Actually have some fun in it, rather than crying everytime I open the garage!

Oh and Phil reminded me of course, 5. Buy more stuff!

[farlow]

Get garage and workshop in to a functional condition and I just might be able to start work on the crx. I'm afraid the Lude won't be seeing much action this year but I will however give it a good wash and move it inside rather than sat on the drive.

[CARRisma]

Get a piece of metal fabricated which the boot lid torsion bar clip slots into because the area under my rear parcel shelf is damaged.

I need to do this as well.

The clip that holds the torsion bars has bent the parcel shelf bit.. I had tried to cable tie them all together but cable ties even made it worse.

Same here. A few years ago, a friend was removing some suitcases from the boot and buggered. The clip bent the metal then snapped it. Shows you how strong the plastic clip is.

[Ammo]

Make it look less like it's due for the scrap yard, then make it look even worse with loads of stickers

It's a Gymkhana car just gonna have fun with it till it dies

[nitin_s1]

I've added some bits on the list.. Maybe its plans for 2014/2015 now.

Just cleaned my garage and shocked to see so many parts waiting to be fit on.
Engine mounts They are for sale.. [If they don't sell then they will go on the car]
De-Cat Not on the car
Red Carpet and Console. DONE
Strut braces (rear) Done
ATR brake set up Done
ATR manifold (still need to find some info and will defo need Emanage before I put this on ) SOLD this.
Motegi Sides Skirts Done
Mugen rear bits and a bonnet bra (not sure if I want them) Sold and don't want it

2014/2015 -

- Get the front end re-spray and minor rust sorted.
- Sort out fuel/air ratio as it's running rich.
- Full exhaust system.
- S2000 steering wheel install.

[CARRisma]

Roughly in order:

• - Replace that broken piece of plastic which holds the bonnet support pole (watch this space for suggested upgraded part). = DONE
  - Clean out inappropriate copper grease from brake caliper slide pins and correctly apply silicone grease (yes, my bad).
  - Get a piece of metal fabricated which the boot lid torsion bar clip slots into because the area under my rear parcel shelf is damaged.
  - Fabricate a cooling plate out of black corrugated plastic.
  - Respray the paint damaged rear skirt.
  - New magnetic sump plug.

http://www.ludegeneration.co.uk/body-wo ... 11548.html

[lxstuart]

No plans this year, but if I get bored I might paint some more of it.
Not necessarily black though.