Congratulations to vtecmec for winning May/June's Lude Of The Month, with his DIY Turbo BB1 build.

>>> Click Here For Profile <<<

Image

Abs 1-2 error code

As much of the Lude knowledge we have in one handy place
Post Reply
User avatar
c_doughty1
Supporter 2014
Posts: 907
Joined: Mon Jul 22, 2013 6:35 pm
My Generation: 4G
Location: Edwinstowe, Nottinghamshire
Been thanked: 2 times

Re: Abs 1-2 error code

Post by c_doughty1 » Thu Mar 24, 2016 8:43 pm

Do you know how to bleed them by any chance I don't I haven't done it yet
Top
User avatar
uberNoobZA
Posts: 430
Joined: Mon Feb 22, 2016 2:49 pm
My Generation: 4G
Location: Oxford / Sanctuary / Azeroth
Has thanked: 17 times
Been thanked: 15 times

Post by uberNoobZA » Thu Mar 24, 2016 8:53 pm

c_doughty1 wrote:Do you know how to bleed them by any chance I don't I haven't done it yet
Nope sorry - Got a mate helping me. We did my Civic when I changed calipers, but that was just removing air bubbles, not a full flush. It was a 2 man manual job with one guy pumping brakes, and another releasing clamp on end of brake line to let brake fluid come out. This went on and on until each brake line showed no more bubbles. Then onto next brake.
Top
User avatar
wurlycorner
Ye are glad to be dead, RIGHT?
Posts: 21493
Joined: Sat May 19, 2012 3:33 pm
My Generation: 4G
Location: Chelmsford, Essex
Has thanked: 2481 times
Been thanked: 306 times

Post by wurlycorner » Thu Mar 24, 2016 9:12 pm

That doesn't bleed the small part of the ABS system that c_doughty is talking about.
Top
User avatar
c_doughty1
Supporter 2014
Posts: 907
Joined: Mon Jul 22, 2013 6:35 pm
My Generation: 4G
Location: Edwinstowe, Nottinghamshire
Been thanked: 2 times

Re: Abs 1-2 error code

Post by c_doughty1 » Thu Mar 24, 2016 9:58 pm

wurlycorner wrote:That doesn't bleed the small part of the ABS system that c_doughty is talking about.
Do you know how to remove the valve on the abs to bleed it? Or an alternative tool that may work.
Top
User avatar
Vtecmec
LotM Winner
Posts: 5490
Joined: Fri Aug 06, 2010 5:43 pm
My Generation: 4G
XBOX GamerTag: vtecmec
Location: East Midlands
Has thanked: 149 times
Been thanked: 441 times

Post by Vtecmec » Thu Mar 24, 2016 10:18 pm

I think you need specialist tools to bleed the abs, plus its under a high pressure. It's the reason I just bypassed my code 1 and left alone......
Top
User avatar
c_doughty1
Supporter 2014
Posts: 907
Joined: Mon Jul 22, 2013 6:35 pm
My Generation: 4G
Location: Edwinstowe, Nottinghamshire
Been thanked: 2 times

Re: Abs 1-2 error code

Post by c_doughty1 » Sat Mar 26, 2016 5:28 pm

Vtecmec wrote:I think you need specialist tools to bleed the abs, plus its under a high pressure. It's the reason I just bypassed my code 1 and left alone......
I may have to take it to honda then.....
Top
kkalle
Posts: 6
Joined: Thu Apr 28, 2016 5:20 pm
My Generation: 4G

Post by kkalle » Fri Apr 29, 2016 6:05 am

You will need a "T-wrench", honda special tool. Shouldn't be a problem to borrow one from your local honda dealer. The bleeding prosses is rather easy.

Jump the abs relay for max 10 seconds, then open the nipple at the pump/motor with the t-wrench. Close nipple again.

Just be careful, due to the possible high pressure.You don't wanna spray brakefluid everywhere.
Top
Post Reply

Return to “Guides / How to's / Tech Section”